碳?xì)淝逑礄C(jī)買了碳?xì)淝逑礄C(jī)后，使用一段時間后，細心的朋友可能會發現他們的碳?xì)淝逑礄C(jī)的功率一天比一天低。情況如何？面對這樣的情況，您別擔心，來看看小編分析的原因您就知道怎么做了。

After buying a hydrocarbon washer, careful friends may find that the power of their hydrocarbon washer is getting lower day by day after using it for a period of time. How is it going? In the face of such a situation, don't worry. Look at the reasons of the minor editor's analysis and you will know how to do it.

碳?xì)淝逑礄C(jī)主要原因是機械設備使用時間過長，變頻調速器逐漸老化，特性降低。維護方法可以選擇提高超聲波輸出功率，但這種維護方法可以治療癥狀而不是根本原因，容易增加換能器的熱量，從而損壞機器。

The main reasons for hydrocarbon cleaning machine are that the mechanical equipment has been used for a long time, the frequency converter is gradually aging, and the characteristics are reduced. The maintenance method can choose to increase the ultrasonic output power, but this maintenance method can treat the symptoms rather than the root cause, which is easy to increase the heat of the transducer, thus damaging the machine.

碳?xì)淝逑礄C(jī)碳?xì)淝逑礄C(jī)的換能器吸濕，絕緣電阻正?；虿糠謸p壞。在這種情況下，好的選擇是拆卸和更換損壞的傳感器。其他原因，電纜是外部損壞還是吸濕，電源電壓過低。

The transducer of the hydrocarbon washer absorbs moisture and the insulation resistance is normal or partially damaged. In this case, a good choice is to remove and replace the damaged sensor. For other reasons, the cable is externally damaged or hygroscopic, and the power supply voltage is too low.

傳感器沒有剝落，在脫膠狀態下，碳?xì)淝逑礄C(jī)的底部不受振動吸收材料或工件的干擾。環中的電源可以移動其工作點并重新調整工作點。超聲波清洗設備的輸出功率較小。更換或修改電源，以增加傳感器的數量。

The sensor does not peel off. Under the degumming state, the bottom of the hydrocarbon washer is not interfered by vibration absorbing materials or workpieces. The power supply in the ring can move its work point and readjust it. The output power of ultrasonic cleaning equipment is small. Replace or modify the power supply to increase the number of sensors.

碳?xì)淝逑礄C(jī)其他未知超聲功率減弱，如放置清潔材料，如，清除和更換清潔劑等。在上述情況下，更有可能損壞超聲波清洗設備的換能器。

Other unknown ultrasonic power of hydrocarbon cleaning machine is weakened, such as placing cleaning materials, such as removing and replacing cleaning agent. Under the above circumstances, it is more likely to damage the transducer of the ultrasonic cleaning equipment.

如果輸出功率低或弱，請先檢查傳感器是否有問題。如果無法判斷原因，應停止使用碳?xì)淝逑礄C(jī)，不要再次使用。但是，隨著輸出功率的降低，可以在有時間的時候?qū)⑵渌突鼐S修。

If the output power is low or weak, check the sensor first. If the cause cannot be determined, stop using the hydrocarbon washer and do not use it again. However, as the output power decreases, it can be sent back for maintenance when there is time.

當然針對維修，您可以先查詢下自己購買產品的廠家怎么樣，售后的服務能不能及時跟上。更多相關內容就來我們網站xxjph.cn咨詢吧！

Of course, for maintenance, you can first inquire about the manufacturer who bought the product and whether the after-sales service can keep up. For more information, please visit our website xxjph.cn!