在使用全自動超聲波清洗機時有一些需要注意的地方，這些是要時刻注意的，操作不當會多機器造成損害甚至引發事故，那超聲波清洗機運行時要謹慎使用什么？看完后操作人員要小心謹慎。

There are some points needing attention when using the full-automatic ultrasonic cleaning machine, which should be paid attention to at all times. Improper operation will cause damage to many machines and even cause accidents. What should be used with caution when operating the ultrasonic cleaning machine? Operators shall be careful after reading.

注意謹慎使用清洗液

Caution: use cleaning fluid with caution

在使用超聲波清洗機的時候，須要按照規范要求的順序進行操作，特別是不可以先開機然后再把清洗液倒進去，這屬于違規操作會引發嚴重的后果甚至?xí)p壞機器，因此一定要先把液體放進去然后再打開開關。同時還應該要顧及到清洗液的成分，如果它含有易燃性質的液體那么一定要在短時間內完成操作，并且全程都要有人監督，不可以離開現場。

When using the ultrasonic cleaning machine, it is necessary to operate in the order required by the specification. In particular, it is not allowed to start the machine first and then pour the cleaning liquid into it. This is an illegal operation, which will cause serious consequences and even damage the machine. Therefore, it is necessary to put the liquid into it first and then turn on the switch. At the same time, the composition of the cleaning liquid should also be taken into account. If it contains flammable liquid, the operation must be completed in a short time, and the whole process must be supervised. It is not allowed to leave the site.

注意使用腐蝕或揮發性清洗液要做特殊處理

Note: corrosive or volatile cleaning solution shall be specially treated

通常情況下是不提倡使用危險性清洗液的，但如果情況比較特殊，強調超聲波清洗機廠家須要使用含有腐蝕性或揮發性的液體，那么應該要采取間接的方式來進行妥善的處理。具體的操作方法是在清洗槽里面先加水，然后再另外用一個容器裝清洗液并放入需要清洗的物品，然后在它們浸入清洗槽的水里面，用這種方式來進行清洗該也會在同樣的效果，又可以保證安全的問題。

In general, it is not recommended to use hazardous cleaning liquid. However, if the situation is special, it is emphasized that the ultrasonic cleaning machine manufacturer needs to use corrosive or volatile liquid, then it should take indirect measures to properly handle it. The specific operation method is to add water to the cleaning tank first, and then use another container to fill the cleaning liquid and put the articles to be cleaned, and then immerse them in the water of the cleaning tank. Cleaning in this way will have the same effect and ensure the safety.

當直接使用易燃液體清洗時，要盡量在短時間內完成清洗工作，并要求操作者不要離開現場。當需要用腐蝕性或揮發性強的清洗液時，可采用間接清洗的方法。即：先在清洗槽內加水，再將所需清洗液倒入適宜的容器內并放入被清洗物，然后將裝有清洗液和清洗物的容器浸入清洗槽中，即可開始清洗工作，其效果與直接清洗相同。

When the flammable liquid is directly used for cleaning, the cleaning shall be completed in a short time as far as possible, and the operator shall not leave the site. When corrosive or volatile cleaning liquid is required, indirect cleaning method can be adopted. That is, add water to the cleaning tank first, then pour the required cleaning liquid into a suitable container and put it into the object to be cleaned, and then immerse the container containing the cleaning liquid and the object into the cleaning tank to start the cleaning. The effect is the same as that of direct cleaning.

全自動超聲波清洗機運行時要謹慎使用什么？以上便是問題的相關解答了，如果您對此有什么疑問或者對設備有需求，就來我們網站xxjph.cn咨詢看看吧。

What should be used carefully when the automatic ultrasonic cleaning machine is running? The above is the relevant answer to the question. If you have any questions or need for equipment, please come to our website xxjph.cn for consultation.